Cooling Tower Biocide
The Dispersant and Biodispersant, which is superiorly used for preventing system from fouling caused by the biological augmentation of slimes, algae and bacterial deposits. On the continuous usage of cooling towers, a biofilm gets generated on the surface due to micro-organisms that can be eliminated by using biodispersants. Our formulations are superlatively known for its features like improvise the efficacy of other biocides, compatible with all biocides and reduce the volume of micro biocides to be dosed.
The chemical formulations offered by us are excellent in putting off Microbiologically Induced Corrosion (MIC). These chemicals are suitable to be utilized in air washers, evaporative condensers, cooling water heat exchangers, blow moulding machines, D.G. sets and various other machines.
Polymeric Dispersant
Samrat Industries Polymeric Dispersant removes the silt deposits from the fins, louvers and pipelines during normal service. It is a polymer and surfactant based product which breaks the clay deposits and remove them with blow down water. It is a neutral pH product and does not cause any corrosion to the system metal during use. It can be dosed manually to the cooling tower sump on a daily basis or can be dosed continuously with a dosing pump.
It works using a combination of chelation, crystal modification and the threshold effect, and is effective against a wide range of scalants including calcium and magnesium hardness, iron oxide and silica. It converts the scaling material into a light mobile floc, which can be blown down easily. It will gradually re-disperse old deposits and may be used as part of a maintenance \92clean up\92 program.
Key Features and Benefits
- Keeps the cooling tower internals pipelines and louvers clean
- Provides high efficiency to the cooling towers working in high dusty area
- Neutral pH product, biodegradable
- Compatible with other chemicals and all metallurgy
Application and Dosage
Treatment and dosage for Samrat Industries Polymeric Dispersant is normally dosed to maintain 50-100 ppm in the system, although, if it is being used as part of a \91clean up\92 programme, higher levels may be maintained.
Samrat Industries Polymeric Dispersant is compatible with other commonly used treatments and can be dosed from the same mixing tank.
For further technical assistance please contact your CSL technical representative.
Handling measures and precautions
Proper human safety products such as Splash goggles, lab coat, vapor respirator, gloves and boots should be worn while handling and applying chemicals. Splashes on skin should be washed off with water immediately. In case of splashing into the eyes, flush it with fresh water and obtain medical attention. Should not be injected. Please refer MSDS for more details.
Storage
This product should be stored in original containers in cool and dry place, away from sources of heat, flame and direct sunlight. Please refer Technical Data Sheet, Label and MSDS for more details and shelf life.
Packing
Samrat Industries Polymeric Dispersant is available in 35 kgs HDPE jars.
Bio Dispersant
Samrat Industries Biodispersant is a bio-dispersant designed for open loop cooling water system with high amount of algae, slime and biofilm contamination.
Samrat Industries Biodispersant cuts and removes the biofilm for increased efficacy of biocides and microbiocides.
Key Features and Benefits
- Controls MIC (Micro-biologically Induced Corrosion)
- Compatible with other oxidizing, non-oxidizing biocides and treatment chemicals
- Completely biodegradable
- Removes biofilms
- Increases biocide efficacy
- Imparts online cleaning cooling tower fills and louvers
- Controls deposition of silt and clay on the CT basis (sump)
- Stable in all pH range and temperatures
Application and Dosage
Samrat Industries Biodispersant should be added directly to the cooling water system with basic procedures. The dosage ranges from 2-20ppm depending on plant condition. Please refer to your CSL service engineer for exact product dosage.
Note : Samrat Industries Biodispersant is slightly foaming in nature
Handling measures and precautions
Proper human safety products such as Splash goggles, lab coat, vapor respirator, gloves and boots should be worn while handling and applying chemicals. Splashes on skin should be washed off with water immediately. In case of splashing into the eyes, flush it with fresh water and obtain medical attention. Should not be injected. Please refer MSDS for more details.
Storage
This product should be stored in original containers in cool and dry place, away from sources of heat, flame and direct sunlight. Please refer Technical Data Sheet, Label and MSDS for more details and shelf life.
Packing
Samrat Industries Biodispersant is available in 35/215kgs HDPE jars and barrels.
Biodispersant Non-Foaming
Samrat Industries Biodispersant Non-Foaming is a heavy duty bio-dispersant designed for cooling water system with very high amount of algae, slime and biofilm contamination.
Samrat Industries Biodispersant Non-Foaming cuts and removes the biofilm for increased efficacy of biocides and microbiocides.
Key Features and Benefits
- Controls MIC (Micro-biologically Induced Corrosion)
- Compatible with other oxidizing, non-oxidizing biocides and treatment chemicals
- Completely biodegradable
- Removes biofilms
- Increases biocide efficacy
- Imparts online cleaning cooling tower fills and louvers
- Controls deposition of silt and clay on the CT basis (sump)
- Stable in all pH range and temperatures
Application and Dosage
Samrat Industries Biodispersant Non-Foaming should be added directly to the cooling water system with basic procedures. The dosage ranges from 5-40ppm depending on plant condition. Please refer to your CSL service engineer for exact product dosage.
Handling measures and precautions
Proper human safety products such as Splash goggles, lab coat, vapor respirator, gloves and boots should be worn while handling and applying chemicals. Splashes on skin should be washed off with water immediately. In case of splashing into the eyes, flush it with fresh water and obtain medical attention. Should not be injected. Please refer MSDS for more details.
Storage
This product should be stored in original containers in cool and dry place, away from sources of heat, flame and direct sunlight. Please refer Technical Data Sheet, Label and MSDS for more details and shelf life.
Packing
Samrat Industries Biodispersant Non-Foaming is available in 35/215kgs HDPE jars and barrels.
CT Fills Cleaner
Samrat Industries CT Fills Cleaner is a unique online cooling tower fills cleaner based on organic biodegradable chemicals. It is effective on white scales, algae-biofoulants and metal oxide (rust) deposits that are found on the fills of cooling towers.
Samrat Industries CT Fills Cleaner is an online product that is self performing and does not incur down-time or man power for CT fills cleaning.
Samrat Industries CT Fills Cleaner also helps in descaling the condenser tubes to some extent. It is effective on calcium carbonate, calcium sulfate and barium sulfate scales.
Key Features and Benefits
- Compatible with other treatment chemicals, FRP, seals and other metallurgy
- Non-Foaming and suitable for online cleaning
- Environmentally responsible - does not contain heavy metals
- Helps to keep the condenser scale free
- Suitable in all pH range
- Does not increase TDS
- Reduces m-alkalinity
- Biodegradable and decomposes to water and oxygen
Application and Dosage
Samrat Industries CT Fills Cleaner should be dosed directly to the cooling tower deck preferably or to the sump (basin), if former is not possible.
The dosage rate shall be:- For light fouling (periodic dosage): 2kg per 10,000ltrs water for thrice a week
For medium fouling:- 5kgs per 10,000ltrs water for thrice a week
For heavy fouling:- 10kgs per 10,000ltrs water for four - five times a week
Samrat Industries CT Fills Cleaner can be dosed at the light fouling dosage once in every week to keep the cooling tower system clean and scale free.
Handling measures and precautions
Proper human safety products such as Splash goggles, lab coat, vapor respirator, gloves and boots should be worn while handling and applying chemicals. Splashes on skin should be washed off with water immediately. In case of splashing into the eyes, flush it with fresh water and obtain medical attention. Should not be injected. Please refer MSDS for more details.
Storage
This product should be stored in original containers in cool and dry place, away from sources of heat, flame and direct sunlight. Please refer Technical Data Sheet, Label and MSDS for more details and shelf life.
Packing
Samrat Industries CT Fills Cleaner is available in 35kgs HDPE jars.
Scale Dispersant
Samrat Industries Scale Dispersant removes the silt deposits from the fins, louvers and pipelines during normal service. It is a polymer and surfactant based product which breaks the clay deposits and remove them with blow down water. It is a neutral pH product and does not cause any corrosion to the system metal during use. It can be dosed manually to the cooling tower sump on a daily basis or can be dosed continuously with a dosing pump.
It works using a combination of chelation, crystal modification and the threshold effect, and is effective against a wide range of scalants including calcium and magnesium hardness, iron oxide and silica. It converts the scaling material into a light mobile floc, which can be blown down easily. It will gradually re-disperse old deposits and may be used as part of a maintenance \92clean up\92 program.
Key Features and Benefits
- Keeps the cooling tower internals pipelines and louvers clean
- Provides high efficiency to the cooling towers working in high dusty area
- Neutral pH product, biodegradable
- Compatible with other chemicals and all metallurgy
Application and Dosage
Treatment and dosage for Samrat Industries Scale Dispersant is dosed to maintain 50-100 ppm in the system, although, if it is being used as part of a \91clean up\92 programme, higher levels may be maintained.
Samrat Industries Scale Dispersant is compatible with other commonly used treatments and can be dosed from the same mixing tank. For further technical assistance please contact your CSL technical representative.
Handling measures and precautions
Proper human safety products such as Splash goggles, lab coat, vapor respirator, gloves and boots should be worn while handling and applying chemicals. Splashes on skin should be washed off with water immediately. In case of splashing into the eyes, flush it with fresh water and obtain medical attention. Should not be injected. Please refer MSDS for more details.
Storage
This product should be stored in original containers in cool and dry place, away from sources of heat, flame and direct sunlight. Please refer Technical Data Sheet, Label and MSDS for more details and shelf life.
Packing
Samrat Industries Scale Dispersant is available in 35 kgs HDPE jars.