Coolant Corrosion Inhibitor
The Coolant Corrosion Inhibitor is used for inhibiting engine or coolant internal surfaces from the attack of corrosion. The products which we cater under this category are Nalcool 2000, Nitrite Based Corrosion Inhibitor, Nitrite Borate & Azole, Nitrite Silicate & Amine Free Corrosion Inhibitor, Glycerine Corrosion Inhibitor and Coolant Thickening Chemical. This inhibitor range is composed from the finest grade rust inhibitors and other compositions to ensure excellent reduction in mineral scale deposits and sludge.
Our inhibitor provides excellent protection to metallic surfaces from corrosion with its unique features like high effectiveness, anti-corrosive, scale prevention, enhance system life and save power. These corrosion inhibitors are used in water treatment plants, cooling towers, chiller water treatment plants and vehicles.
Nalcool 2000
Samrat Industries NALCOOL 2000 is a multifunctional blend of nitrite based corrosion inhibitors for engine system. It prevents corrosion or rusting of metal by forming a passive coating of protective film on the metal surface. Samrat Industries NALCOOL 2000 contains a combination of ferrous and non-ferrous corrosion inhibitor, non-carbonate buffer, scale inhibitor, dispersant and leak detection dye.
Active Components: Nitrite, Nitrate, TT, Borate, Silicate and Polyacrylate for Aluminum, MS, Copper and Cu-alloys
Key Features and Benefits
- Multi-metal corrosion protection
- Scale prevention
- Saves power more than 30%
- Temperature resistance - 29°C to 215°C
- Leakage and burst protection
- Extends system life
- Enhances system efficiency
Application and Dosage
System Preparation: To remove all dirt deposits, oil and rust particles, run the engine for 24-72 hours with 2ltrs ALSTACLEAN RC50 for every 30ltrs of fresh water/coolant and then drain the dirty solution. Flush engine with fresh water and add fresh water/coolant with Samrat Industries NALCOOL 2000 in the indicated ratio (1ltr for every 32ltrs of water/coolant).
Initial dose: Add Samrat Industries NALCOOL 2000 - 1ltr for every 32ltrs of water/coolant to maintain a nitrite level of about 1200ppm. To maintain a correct inhibitor level in the system, it is necessary to always top-up the system with Samrat Industries NALCOOL 2000 during make-up requirement of plain water/coolant
Regular dose (for small system less than 80ltrs): Add Samrat Industries NALCOOL 2000 - 1ltr for every 32ltrs of water/coolant after every 20,000kms or 250hours or running.
Regular dose (for large system above 80ltrs): Add Samrat Industries NALCOOL 2000 - 1ltr for every 80ltrs of water/coolant at every routine service.
Shelf life in use: Samrat Industries NALCOOL 2000 should be drained and flushed once every year
Handling measures and precautions
Proper human safety products such as Splash goggles, lab coat, vapor respirator, gloves and boots should be worn while handling and applying chemicals. Splashes on skin should be washed off with water immediately. In case of splashing into the eyes, flush it with fresh water and obtain medical attention. Should not be injected. Please refer MSDS for more details.
Storage
This product should be stored in original containers in cool and dry place, away from sources of heat, flame and direct sunlight. Please refer Technical Data Sheet, Label and MSDS for more details and shelf life.
Packing
Samrat Industries NALCOOL 2000 is available in HDPE containers of various sizes.
Nitrite Based Corrosion Inhibitor
Samrat Industries NITRITE BASED CORROSION INHIBITOR is a superior blend of multi-metal corrosion inhibitors for closed loop system containing chiller or hot water. It prevents corrosion or rusting of metal by forming a passive coating of protective oxide film on steel.
Samrat Industries NITRITE BASED CORROSION INHIBITOR also contains a special yellow metal (copper) corrosion inhibitor,that protects copper and its alloys such as cupro-nickel, brass etc., from corrosion.
In case of hardness ingress Samrat Industries NITRITE BASED CORROSION INHIBITOR prevents scaling and deposition of calcium and magnesium hardness and iron deposits. Thus keeping the heat exchange at best efficiency.
Key Features and Benefits
- Multi-metal corrosion protection
- Scale prevention
- Saves power more than 30%
- Non-foaming
- Leakage and burst protection
- Extends system life
- Extends fluid or glycol life
- No descaling of Heat exchangers
Application and Dosage
Samrat Industries NITRITE BASED CORROSION INHIBITOR is a nitrite based system corrosion inhibitor program and should be added directly to the system in its neat form or diluted with clean, soft water to give a desired nitrite level. It can be dosed directly to the make up tank or with metered injection dosing pump into the closed circuit. The nitrite level varies from 600-2400 ppm (as NO2) depending upon the application.
Please refer to your CSL service engineer for exact product dosage.
Note : Nitrite based program is a completely organic and biodegradable program, for this reason, the nitrite is degraded by bacteria. A non-oxidising biocide such as Important ALSTACIDE CW30 at 50-100ppm dosage will prevent this degradation.
Handling Measures and Precautions
Proper Human Safety Products Such As Splash Goggles, Lab Coat, Vapor Respirator, Gloves And Boots Should Be Worn While Handling And Applying Chemicals. Splashes On Skin Should Be Washed off With Water Immediately. In Case of Splashing Into The Eyes, Flush It With Fresh Water And Obtain Medical Attention. Should Not Be Injected. Please Refer Msds For More Details.
Storage
This Product Should Be Stored In Original Containers In Cool And Dry Place, Away From Sources of Heat, Flame And Direct Sunlight. Please Refer Technical Data Sheet, Label And Msds For More Details And Shelf Life.
Packing
Samrat Industries NITRITE BASED CORROSION INHIBITOR is available in 35/220kgs HDPE jars and barrels.
Nitrite Borate and Azole
Samrat Industries NITRITE BORATE AND AZOLE is a superior blend of multi-metal corrosion inhibitors for closed loop system containing glycol and water. It prevents corrosion or rusting of metal by forming a passive coating of protective oxide film on the metal surface and by removing the dissolved oxygen in the system which results in glycol degradation to form into five organic acids viz., Glycolic Acid, Glyoxalic Acid, Formic Acid, Carbonic Acid and Oxalic Acid.
Samrat Industries NITRITE BORATE AND AZOLE also contains a special yellow metal (copper) corrosion inhibitor, that protects copper and its alloys such as cupro-nickel, brass etc., from corrosion.
Key Features and Benefits
- Multi-metal corrosion protection
- Saves power more than 30%
- Non-foaming
- Enhances cooling efficiency
- Added oxygen scavenger
- Leakage and burst protection
- Extends system life
- Extends fluid or glycol life
- No descaling of Heat exchangers
Application and Dosage
Samrat Industries NITRITE BORATE AND AZOLE is a nitrite based system corrosion inhibitor program and should be added directly to the system in its neat form or diluted with clean, soft water to give a desired nitrite level. It can be dosed directly to the make up tank or with metered injection dosing pump into the closed circuit. The nitrite level varies from 600-2400 ppm (as NO2) depending upon the application.
It also contains an oxygen scavenger which removes the dissolved oxygen from the system and prevents glycol degradation and oxidation corrosion.
Please refer to your CSL service engineer for exact product dosage.
Note : Nitrite based program is a completely organic and biodegradable program, for this reason, the nitrite is degraded by bacteria. A non-oxidising biocide such as ALSTACIDE CW30 at 50-100ppm dosage will prevent this degradation.
Handling Measures and Precautions
Proper Human Safety Products Such As Splash Goggles, Lab Coat, Vapor Respirator, Gloves And Boots Should Be Worn While Handling And Applying Chemicals. Splashes On Skin Should Be Washed off With Water Immediately. In Case of Splashing Into The Eyes, Flush It With Fresh Water And Obtain Medical Attention. Should Not Be Injected. Please Refer Msds For More Details.
Storage
This Product Should Be Stored In Original Containers In Cool And Dry Place, Away From Sources of Heat, Flame And Direct Sunlight. Please Refer Technical Data Sheet, Label And Msds For More Details And Shelf Life.
Packing
Samrat Industries NITRITE BORATE AND AZOLE is available in 35/220kgs HDPE jars and barrels.
Nitrite Silicate and Amine Free Corrosion Inhibitor
Samrat Industries NITRITE SILICATE AND AMINE FREE CORROSION INHIBITOR is a specially formulated chemical additive for Mono Ethylene Glycol to protect system metals from corrosion. It is a multi-metal corrosion inhibitor and prevents corrosion in multi-ways.
Samrat Industries NITRITE SILICATE AND AMINE FREE CORROSION INHIBITOR modifies metal surface by absorption and making it less susceptible to corrosion. It buffers the organic acids formed as a result of glycol oxidation and prevents further formation of acids. Samrat Industries NITRITE SILICATE AND AMINE FREE CORROSION INHIBITOR protects the metal surface from corrosion without reducing the system\92s heat transfer efficiency.
Mono Ethylene Glycol oxidizes when exposed to air and heat. When this occurs, five organic acids viz., Glycolic, Glyoxalic, Formic, Carbonic and Oxalic Acid are formed. If not properly inhibited, this fluid gets very corrosive. These organic acids then chemically attacks and corrodes the system metal, causing pitting, pinhole and stress cracking corrosion.
Samrat Industries NITRITE SILICATE AND AMINE FREE CORROSION INHIBITOR is added to Ethylene Glycol to act as buffer, preventing low pH attack on the metals. It also passivates the metal surface to protect them from corrosion.
Key Features and Benefits
- Extends system/engine metal life and coolant life
- Saves power and increases heat transfer efficiency
- Hard water tolerant and prevent scale deposition up to 200ppm calcium hardness
- Does not affect Freeze protection properties
- Does not form sludge deposit in the system
- Avoids leakage and minimizes radiator cleaning jobs
- Compatible with all sorts of coolant dye
- Non-volatile
Handling Measures and Precautions
Proper human safety products such as Splash goggles, lab coat, vapor respirator, gloves and boots should be worn while handling and applying chemicals. Splashes on skin should be washed off with water immediately. In case of splashing into the eyes, flush it with fresh water and obtain medical attention. Should not be injected. Please refer MSDS for more details.
Storage
This product should be stored in original containers in cool and dry place, away from sources of heat, flame and direct sunlight. Please refer Technical Data Sheet, Label and MSDS for more details and shelf life.
Packing
Samrat Industries NITRITE SILICATE AND AMINE FREE CORROSION INHIBITOR is available in various pack sizes.
Glycerine Corrosion Inhibitor
Samrat Industries GLYCERINE CORROSION INHIBITOR is a specially formulated chemical additive for glycerine to protect system metals from corrosion. It is a multi-metal corrosion inhibitor and prevents corrosion in multi-ways.
Samrat Industries GLYCERINE CORROSION INHIBITOR modifies metal surface by absorption and making it less susceptible to corrosion.
Key Features and Benefits
- Extends system metal life
- Increases life of Glycerine by avoiding degradation
- Does not form sludge deposit in the system
- Avoids leakage and minimizes maintenance jobs
Handling Measures and Precautions
Proper human safety products such as Splash goggles, lab coat, vapor respirator, gloves and boots should be worn while handling and applying chemicals. Splashes on skin should be washed off with water immediately. In case of splashing into the eyes, flush it with fresh water and obtain medical attention. Should not be injected. Please refer MSDS for more details.
Storage
This product should be stored in original containers in cool and dry place, away from sources of heat, flame and direct sunlight. Please refer Technical Data Sheet, Label and MSDS for more details and shelf life.
Packing
Samrat Industries GLYCERINE CORROSION INHIBITOR is available in 35kgs HDPE carboys
Coolant Thickening Chemical
Samrat Industries COOLANT THICKENING CHEMICAL is an organic product derived from plant extracts to impart a cosmetic effect to the aqueous solution by increasing the thickness of a water / glycol based industrial / automotive coolant.
Samrat Industries COOLANT THICKENING CHEMICAL is designed in such a way that it will not have any side effect on the metals (aluminum, copper, cast iron, steel etc.), rubber hoses, seals and other engine component and will pass through the glassware corrosion test.
In addition, Samrat Industries COOLANT THICKENING CHEMICAL also has a significant advantage that it looses its thickening properties when it is added to the engine. This helps by not causing a high pumping load on the radiator.
Key Features and Benefits
- Enhances the cosmetic view, touch and feel of the coolant
- Disintegrates when the solution is vigorously shaken, such as in an engine
- Derived from plant extracts - completely biodegradable, organic and skin friendly
- Does not interfere in the chemical properties of the coolant
- Available in liquid emulsion, hence easy to dose and mix
Handling Measures and Precautions
Proper human safety products such as Splash goggles, lab coat, vapor respirator, gloves and boots should be worn while handling and applying chemicals. Splashes on skin should be washed off with water immediately. In case of splashing into the eyes, flush it with fresh water and obtain medical attention. Should not be injected. Please refer MSDS for more details.
Storage
This product should be stored in original containers in cool and dry place, away from sources of heat, flame and direct sunlight. Please refer Technical Data Sheet, Label and MSDS for more details and shelf life.
Packing
Samrat Industries COOLANT THICKENING CHEMICAL is available in 20kgs HDPE jars